[Blkoutsrt8]

Getting my lc1 wide band wondering how hard it is to connect it to trinity??? What else do I need to get this thing connected

 

[bcm0018]

Its been discussed on here before if you do a search, also the diablosport forum has good information on it too.

 

[Blkoutsrt8]

I used search function nothing came up

 

[ekaz]

I used search function nothing came up

Really? I entered "trinity lc1" in the search box and bingo....

http://www.cherokeesrt8.com/forums/showthread.php?t=46953&highlight=trinity+lc1

 

[Blkoutsrt8]

I Tried on iPhone idk I entered lc1 wideband to trinity lol

 

[Jeep Trick]

Did you buy the LC-1 as a stand alone with out a gauge?

If so follow the instructions and install it as normal. Don't worry about hooking it up to the trinity till you verify its working on it own. Remember to follow the calibration instructions or you will not get an accurate reading. If you don't have a gauge you will need to use the red led and switch provided with the LC1 to go through the calibration.

Once you know it working via the led all you have to know is which wire out of the LC1 and which analog wire in for the trinity to connect to each other

Remember you can call tech if you have a question.

 

[Blkoutsrt8]

Yea no gauge and thanks for that info!

 

[Blkoutsrt8]

so i have everything wired just need help setting up on the trinity..i find all info for going from AEMgauge to trinity but no LC1 to trinity.

 

[Knuckles]

so i have everything wired just need help setting up on the trinity..i find all info for going from AEMgauge to trinity but no LC1 to trinity.

Low number is 7.35 AFR (0V) and high number is 22.39 AFR (5V) for th Innovate LC 1.

 

[Blkoutsrt8]

Thanks!!!!

 

[Knuckles]

Thanks!!!!

Anytime! Make sure you know which input you have wired on this 2.5mm cable, so that you are configuring the right input on the Trinity...

 

[Blkoutsrt8]

answered own question...thanks! again

 

[Knuckles]

answered own question...thanks! again

Cool......

 

[Blkoutsrt8]

anyone know where i can find the software online that comes on the CD..left that at home and im at work which is dead and want to get this thing rollin!

 

[Knuckles]

anyone know where i can find the software online that comes on the CD..left that at home and im at work which is dead and want to get this thing rollin!

Go to innovate motorsports website....Downlown the Logworks 3.07 software, which will have the LM Programmer software that you need to check the settings on your LC1..

http://www.innovatemotorsports.com/support.php

 

[Blkoutsrt8]

once u have it hooked up do ur log and wanna view it in DATA viewer what do you click off to see AFR?

 

[Knuckles]

once u have it hooked up do ur log and wanna view it in DATA viewer what do you click off to see AFR?

Go to the bottom left hand corner and under External you will see Analog inputs... Look for what ever you called that analong input. Mine shows up as Wideband (AFR)

 

[Blkoutsrt8]

Thanks Knuckles you been a big help for me!

 

[Knuckles]

Thanks Knuckles you been a big help for me!

Anytime bro!

 

[diegom6]

Resurecting a old thread, but maybe someone could point me out how to "connect" the LC-1 OUT wire into the Trinity T1000? Can't find much info on this subject.

For example I know I can use the brown wire of the LC-1 for the output signal into the Trinity, but where do I conenct this wire in the Trinity? There is a flat connection next to the main plug that goes into the OBDII port, but AFAIK, the Trinity didn't come with that extra falt connector wiring, is this a special connector/wiring that need to be ordered separately?

What I need is to "log" the AFR into the Trinity for some "external tune" with the tuner (through emails) as I'm having some tuning issues witht he 426 stroker engine we just builded.

Thanks for any sugegstion/help

-Diego