Has any Vendors done or is doing a group buy on underdrive pullies,would there be any intrest in this or just me.

Newfie.

x2............

Im sure down for one

We will host it if you want. I have 20 sitting on the shelf right now. I just need to get more belts in, but thats easy enough. How much interest is there? I will sell for the following.

5-10 units: $175 plus $20 for bolt/belt
11+ units: $150 plus $20 for bolt/belt

Shipping is additional and usually around $15.

make that 4.

make it 5......

whats should we expect for power increase of this?

9-14 rwhp is what we have seen.

9-14 rwhp is what we have seen.

How is the install?

Also, are there any charging issues? I'd probably be interested:D

Yeah I'm kinda interested in this.

I have installed a couple of these and we didn't see any negative effects on charging or accessories.

As far as the install goes, I haven't completed one on a GCSRT yet, my pulley should be here end of this week or sometime next week.

Officially, you're supposed to drain the radiator and remove the upper radiator hose, however, I've read that you can install from the bottom if you get it up on jackstands or ramps.
I will report back once I go to install mine.

Thanks! How is the install? How long does it take? I have a lift, do you think that would make it easier?

Thanks, Derek

Thanks! How is the install? How long does it take? I have a lift, do you think that would make it easier?

Thanks, Derek

If working from underneath works, the lift will definitely help. If you have the right rools, an idea of what you're doing, I'd say maybe a few hours, depending.
I can't say for sure as I haven't installed one on a Jeep yet. There seems to be more room on the Jeep than on an LX car.

figure 3-4 hours doing it yourself.

Here is the list of interested parties. Copy the list and add your name to the bottom. This is not a definite list, just those that are interested.
The pricing listed by PPP:
5-10 units: $175 plus $20 for bolt/belt
11+ units: $150 plus $20 for bolt/belt

Shipping is additional and usually around $15.

1. Newfiebullet
2. RedRockerSRT
3. Get$$$Man
4. CustomCaddys
5. blown454nova
6. kcshaner
7. Kausekaos

Andy,
Did you want to put a timeframe on this?

I dont mean to jump on PPPs thread but I do have some answers that might help those on the fence.


Install time is prob right about 1 hour if you preheat the pulley in your oven.

I have 2 amps and a single sub in my Jeep and Ive idled for 20 minutes with no problems. At idle Im still seeing over 13 volts charging at the battery.

You do not need a lift, I was lazy and drove my Jeep on a 4x4 block and did it in the garage. You will need to have a impact gun to remove the crank bolt and install it back on, it can be done without but that will add time to the install. Autozone will loan you the crank pulley removal tool, the reason I say to heat the pulley in a oven is so you dont need the longer bolt others have had to make or find. If you heat the pulley, you can bang the pulley with a block of wood and small beater enough to get the bolt to draw it in.

I think it was a worth while mod but I did a ported intake at the same time, my gains were around 4/10ths in the 1/4 mile but I dont know what came from what mod.

Here is the list of interested parties. Copy the list and add your name to the bottom. This is not a definite list, just those that are interested.
The pricing listed by PPP:
5-10 units: $175 plus $20 for bolt/belt
11+ units: $150 plus $20 for bolt/belt

Shipping is additional and usually around $15.

1. Newfiebullet
2. RedRockerSRT
3. Get$$$Man
4. CustomCaddys
5. blown454nova
6. kcshaner
7. Kausekaos
8. JohnsonSRT8

I dont mean to jump on PPPs thread but I do have some answers that might help those on the fence.


Install time is prob right about 1 hour if you preheat the pulley in your oven.

I have 2 amps and a single sub in my Jeep and Ive idled for 20 minutes with no problems. At idle Im still seeing over 13 volts charging at the battery.

You do not need a lift, I was lazy and drove my Jeep on a 4x4 block and did it in the garage. You will need to have a impact gun to remove the crank bolt and install it back on, it can be done without but that will add time to the install. Autozone will loan you the crank pulley removal tool, the reason I say to heat the pulley in a oven is so you dont need the longer bolt others have had to make or find. If you heat the pulley, you can bang the pulley with a block of wood and small beater enough to get the bolt to draw it in.

I think it was a worth while mod but I did a ported intake at the same time, my gains were around 4/10ths in the 1/4 mile but I dont know what came from what mod.

Thanks for the info, but I want to caution everyone. I would not stick it in the oven as there are rubber bands inside the pulley itself to help with the dampning. I would just heat up the snout end with a torch or hot oil.

Andy,
Did you want to put a timeframe on this?

Let go till we hit 11 and then we will create link for everyone and start shipping.

Bro, its not like I heated it up to 500 degrees or anything.

I would hope the quality of these things can take more than 200 degrees.

Bro, its not like I heated it up to 500 degrees or anything.

I would hope the quality of these things can take more than 200 degrees.


LOL. There are a ton of parts on the outside of the engine that would not survive more than 200 degrees.

This is cool if we can get it for 170 that's a good deal. Everyone should search for some of Marios threads he's had great success with this and for people around the tri-state area he had it installed professionally by a certified SRT tech that does good work around here. I believe his name here is magnumman but he is more on the lx sites.

I'd be a little nervous about installing it myself but I would def wanna try if I knew I had all the right tools and know-how.

Thanks ppp hope this works out!

This just came to my mind seeing on how im doing a cam install at the same time,but i dod not expect so many to be interested.LOL

Newfie.

The best time to install it is with a cam swap since the pulley has to come off for it.

im pretty interested if i can put it on my 5.7L

Cant beat that price

1. Newfiebullet
2. RedRockerSRT
3. Get$$$Man
4. CustomCaddys
5. blown454nova
6. kcshaner
7. Kausekaos
8. JohnsonSRT8
9. ajharman

LOL. There are a ton of parts on the outside of the engine that would not survive more than 200 degrees.


We arent speaking about the ton of parts here that cant take 200 degrees.
We are speaking about a specific pulley where coolant temps on a stock vehicle can run over 215, oil temps run over 230 degrees. My oven method is no different than you puting a torch to it, you know aluminium is a excellent conductor of heat and I would bet the rubber reaches pretty darn close to the temps I saw in the oven.


Just reread your original post, good luck on that 4 hour install, like I said it took me around a hour in my garage ;) I didnt spend 4 hours total removing the intake twice and installing my pulley :D

many people have different ways to do things, i have used bearing heaters to heart balancers and pulleys before, as well as torches and ovens. Everyone also works on there own pace with there own experience and mechanical ability.

I think we all know this... no need for anyone to get upset or offended

Someone should just do a detailed write up for us mechanically challenged folk

Wow, we are arguing over something so trivial. Its easy for you to stick something in the oven as you are responsible for your own actions. If I tell someone to stick a part in the oven and it fails, it is on me. Your instructions are extremely vague, you didnt say what temp or how long or nothing, me applying a torch to it does not get the front end hot at all where the bands are located. As for your 1 hour install, congrats, but Im not going to tell someone 1 hour when realisticly for your average DIY person it will be closer to 3 hours. How did this thread become an attack on my ability to install a pulley, not once have I said anything about how long it takes me. Some ego you must have to sit back and say "it only took me one hour". You know what, send me your address so I can send you a cookie for your superb installation capability, better yet, I will send you some cookie dough and you can put them in the oven with your next pulley. LOL.

You are correct it is so trival but now your back tracking, you didnt say not to heat it in the oven, I DID. How will that ever fall back on you ? Vague instructions, its a pretty basic job and if the installer doesnt have a clue, he prob shouldnt attempt. You corrected me, there is nothing wrong with my way, it works as does the torch. Blown454Nova got it correct and about sums up this thread.


Please do send the cookie dough but I wont cook it, I like it raw and in my ice cream :cool: Good luck, it apprears that you have earned at least 10 sales thru this post. :wave:

Come on Fellas,there must be 2 more people that need or want this pully!!!2 more and we get a great price of 150 bucks and you cant beat that.

Newfie.

Someone should just do a detailed write up for us mechanically challenged folk


This will about cover it, not trying to offend anybody but if this isnt good enough for you you prob need to pay someone to complete the job.

1) Heat oven to lowest setting or 200 Degrees :D

2) Get a ratchet and remove the original FEAD belt (Take note of how it is routed)

3) Use the Chrysler Pulley removal tool to remove the stock pulley (This tool can borrowed from Autozone or OReiley) You are going to need to have a impact gun at this point, if you dont have a impact gun you prob need to stop because you can remove the pulley but will not get the new one on.

4) Wear oven mitts and dont burn yourself on the hot pulley (If you didnt know that stop what your doing :D )

5) Use a wooden block and small beater to get new pulley to go as far into crank as possible or at least until a few threads from bolt grab.

6) Hit the bolt with a impact gun until pulley is driven into crank, the pulley needs to be aligned with rest of pullies so belt wont jump.

* You will need to remove fan assembly if your impact gun doesnt fit, If memory serves me correct there are 4 bolts(either 8mm-5/16ths or 10mm) you will also need to remove coolant hose to pull the fan assembly upwards


Guys its a really easy install just like the intake, your only problem will be the need for a impact gun.

BUMP 2 more people!!!

Allright beeotchs...... I'm in. This is the SLP one correct?

1. Newfiebullet
2. RedRockerSRT
3. Get$$$Man
4. CustomCaddys
5. blown454nova
6. kcshaner
7. Kausekaos
8. JohnsonSRT8
9. ajharman
10. Harrison

Allright beeotchs...... I'm in. This is the SLP one correct?


Im wondering the same thing? I'm assuming it is :thinkerg:

SLP does not manufacture a pulley. PowerBond is the manufacture and we buy it direct from them.

SLP does not manufacture a pulley. PowerBond is the manufacture and we buy it direct from them.

So my "SLP" pulley is actually made by Powerbond?

This is a great price on these....I just want to see what the long term affects these have on the engines before hopping on this train...

This is a great price on these....I just want to see what the long term affects these have on the engines before hopping on this train...

The long term effects on the engine are non-existent from my experience. I've had under drive pulley sets on every vehicle I've ever owned. Never been the cause of any motor problems I've dealt with. And btw, I've been working on cars for 14 years, and my install time was just over 2 hours. So this guy who did it in 1 hour must be a damn prodigy! I kinda liked that whole oven baked goodness method. :cool:

Is the one more person?one more and we get it for 150 bucks!!!!come on guys one more.


Newfie.

Will you help me install one Mike?

So my "SLP" pulley is actually made by Powerbond?

Good question.....

Hell yeah Tony,after im done with mine here in march we can pop yours on and it will be ready for may.

Newfie.

I'm not doing anything before may. I want to use the track day's times to base the rest of my work off of. That way we'll have some true stock numbers to work with. PS let's get together soon, I want to hear that thing!

But yeah ill help you any time,i got my cam today so now im waiting on headers and a few other things.

Newfie.

1. Newfiebullet
2. RedRockerSRT
3. Get$$$Man
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison

Kausekaos removed per his request.

Wait take me off the list. I just bought bwoody springs instead.

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison

Kausekaos removed per his request.


I'll take one too I guess if it's not too late. Let me know

You are on the list.

1. Newfiebullet
2. RedRockerSRT
3. Get$$$Man
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king

So andy theres 11 of use so its 150 for the pully right + 20 for the belt and crank bolt right.Let us know how to order for these prices.

Newfie.

What's the price drop to if the list grows to 15? :)

Yay GRIPPP!!!!!!! So its the same pulley as the SLP one?

125+20 for 15! come on andy

^^^^^^^^^^ yea

I'm ready for my pulley, when are they shipping? :D

If the pulley is the same for the 5.7 someone sign me up....

ill take one for the 5.7L to

If I remember correctly, it is the same pulley for the 5.7's. Andy can verify. If that is the case, then we are up to 13?

when will this deal be finalized? who and when are we gonna pay?

Andy stated earlier that he would post the purchasing info once we got to 11, so just waiting on him.

seeing that they're racking up fast and all..

$150.00 Shipped with belt for 20?

^^^^^ yea sounds good to me. I bet this group buy could get even larger than 20.

BUMP

You are on the list.

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king

So andy theres 11 of use so its 150 for the pully right + 20 for the belt and crank bolt right.Let us know how to order for these prices.

Newfie.

Please add me to the list...pulley + bolt & belt.

I'm interested, but I'm no mechanic by far so how hard would the install be, or better yet I wonder how much a mechanic would charge me to install it?

If it's say a 2 hour job maybe what 120-150 for install?

Where are ya Andy,i think most of use are ready to do this,i also sent you a PM,we are waiting on you Buddy.

Newfie.

Christ almighty!!! I've checked my mailbox the past two days and still no pulley, are they ever going to ship? :)

Im in, add me to the list. I been looking for this

if the price drops again i'll jump back on this. lol

Im in, add me to the list. I been looking for this

add yourself to the list foooooooooooooo!

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king
12. jsjahonda(big BK)

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king
12. jsjahonda(big BK)

Can someone add me to the list too? :)

You are on the list.

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king
12.jsjahonda(big BK)

So andy theres 11 of use so its 150 for the pully right + 20 for the belt and crank bolt right.Let us know how to order for these prices.

Newfie.
I'm on the list;)

Can someone add me to the list too? :)

You're already there, number 9

You're already there, number 9

Oh, thanks. ;)

just so i know how much are these regularly

just so i know how much are these regularly

about $235 with belt, this is not with shipping

I'm going to be up visiting friends in college for the next few days. So I prob wont be able to pay til next week. Just keep me on the list!!!!

OK. Add me to the list also

Please add me to the list...pulley + bolt & belt.
Forgot to add myself to list. :o

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king
12. jsjahonda(big BK)
13. kilr4d

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king
12. jsjahonda(big BK)
13. kilr4d
14. scoutermike

Add me to the list since I prob melted the rubber when I put it in the oven :D

Hey Andy, I dont think I have seen you respond. Is this the same exact pulley as the SLP version ? Perhaps thats why yours melts in the oven ;)

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king
12. jsjahonda(big BK)
13. kilr4d
14. scoutermike
15. Btlfed (Betty Crocker) ;)

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king
12. jsjahonda(big BK)
13. kilr4d
14. scoutermike
15. Btlfed (Betty Crocker)
16. Kausekaos

screw it lets spend more money

yea guys the more the cheaper lets do it.

1. Newfiebullet
2. RedRockerSRT
3. Get$$
4. CustomCaddys
5. blown454nova
6. kcshaner
7. JohnsonSRT8
8. ajharman
9. Grip Grip
10. Harrison
11.retro-king
12. jsjahonda(big BK)
13. kilr4d
14. scoutermike
15. Btlfed (Betty Crocker)
16. Kausekaos
17. Hemi.Jon (only if it fits 5.7L)

Add me to the list since I prob melted the rubber when I put it in the oven :D

Hey Andy, I dont think I have seen you respond. Is this the same exact pulley as the SLP version ? Perhaps thats why yours melts in the oven ;)



SLP does not manufacture a pulley. They buy the PowerBond and put their name on it. It is the exact same pulley.


Sorry it has taken me so long to respond. i have been in the hospital this week sick. I have to go back today for blood test results, so it still may be hard to reach me till tomorrow or Monday. I am putting the group buy on the website right now. i can not go any lower than I already have otherwise I will be loosing money on each sale. The pulley works on the 5.7 cars, but not the 5.7 jeeps/trucks. The 5.7 jeep/truck has different accessories and an 8-rib setup compared to the 6-rib on the cars. The off-set is slightly different also.

Here is the link to the pulley.
http://purehorsepowerperformance.com/25underdrivepulley.aspx

SLP does not manufacture a pulley. They buy the PowerBond and put their name on it. It is the exact same pulley.


Sorry it has taken me so long to respond. i have been in the hospital this week sick. I have to go back today for blood test results, so it still may be hard to reach me till tomorrow or Monday. I am putting the group buy on the website right now. i can not go any lower than I already have otherwise I will be loosing money on each sale. The pulley works on the 5.7 cars, but not the 5.7 jeeps/trucks. The 5.7 jeep/truck has different accessories and an 8-rib setup compared to the 6-rib on the cars. The off-set is slightly different also.

Here is the link to the pulley.
http://purehorsepowerperformance.com/25underdrivepulley.aspx

Dude! I just checked into the site and was ready to buy, but then i saw 31.45 to ship to FL 34997! WTF! That is pretty ridiculous! Shipping price is way out of line especially for a 7.5 lb pulley! Almost feel like I'm buying from ebay! LOL!

Seriously, any chance pf getting actual shipping costs?

Dude! I just checked into the site and was ready to buy, but then i saw 31.45 to ship to FL 34997! WTF! That is pretty ridiculous! Shipping price is way out of line especially for a 7.5 lb pulley! Almost feel like I'm buying from ebay! LOL!

Seriously, any chance pf getting actual shipping costs?


shouldnt be anymore that $15-$20. Try again, I am adjusting the weight of the item. i had it listed as 12 lbs. Try it again.

Paid...... What's quicker? USPS PArcel Post or Priority Post?

Paid...... What's quicker? USPS PArcel Post or Priority Post?

Priority is way faster than Parcel. Usually 2-3 days compared to 6-7.

are these ready to buy group style on your website andy?

Good b/c I did do Priority.

Dam you all with this group buy. This Jeep is stealing all my $$$. Paid

SLP does not manufacture a pulley. They buy the PowerBond and put their name on it. It is the exact same pulley.


Sorry it has taken me so long to respond. i have been in the hospital this week sick. I have to go back today for blood test results, so it still may be hard to reach me till tomorrow or Monday. I am putting the group buy on the website right now. i can not go any lower than I already have otherwise I will be loosing money on each sale. The pulley works on the 5.7 cars, but not the 5.7 jeeps/trucks. The 5.7 jeep/truck has different accessories and an 8-rib setup compared to the 6-rib on the cars. The off-set is slightly different also.

Here is the link to the pulley.
http://purehorsepowerperformance.com/25underdrivepulley.aspx

I'm trying to checkout, but it won't accept a Canadian address????? :mad:

I'm trying to checkout, but it won't accept a Canadian address????? :mad:

You can paypal to performance@powerported.com. Do $150 for the pulley, $20 for the belt/bolt, and $20 shipping and we will get it shipped out. We will start shipping these tomorrow. Thanks guys.

You can paypal to performance@powerported.com. Do $150 for the pulley, $20 for the belt/bolt, and $20 shipping and we will get it shipped out. We will start shipping these tomorrow. Thanks guys.
:cool:

Paid.

shouldnt be anymore that $15-$20. Try again, I am adjusting the weight of the item. i had it listed as 12 lbs. Try it again.

Much better, but... Actually, there is still a problem though... Paid through paypal. Total bill was supposed to be 184.05 but after sending payment the bill inflated to 191.48. What's up with that? Not trying to be a cheap ass, but the deal was supposed to be 184.05 when I paid! That's it! After payment, all of a sudden there is a 3.75 surcharge that I didn't agree to, which would then make the bill. 187.80. Then there is an additional amount of 3.98 that the bill says nothing about! What's up with that?

I guess my wife being a CPA is getting the better of me! It's her fault! LOL!

Much better, but... Actually, there is still a problem though... Paid through paypal. Total bill was supposed to be 184.05 but after sending payment the bill inflated to 191.48. What's up with that? Not trying to be a cheap ass, but the deal was supposed to be 184.05 when I paid! That's it! After payment, all of a sudden there is a 3.75 surcharge that I didn't agree to, which would then make the bill. 187.80. Then there is an additional amount of 3.98 that the bill says nothing about! What's up with that?

I guess my wife being a CPA is getting the better of me! It's her fault! LOL!

On group buys we always have a 3% suurcharge to cover credit card fee. Im not sure what the 3.98 fee is, I will call tech support to find out. It looks like the surcharge might be in there twice. I can send you a $3 gift certificate if it helps?

On group buys we always have a 3% suurcharge to cover credit card fee. Im not sure what the 3.98 fee is, I will call tech support to find out. It looks like the surcharge might be in there twice. I can send you a $3 gift certificate if it helps?

LOL! what the hell am I gonna do with a $3 gift certificate? :confused: Hey, maybe I can buy some valve stem caps, got any of those? LOL! I don't give a crap, just get me the damn pulley ASAP! :D

Payment sent. Bring on the pulley. Now I have to figure out how to install it lol

Payment sent!

On group buys we always have a 3% suurcharge to cover credit card fee. Im not sure what the 3.98 fee is, I will call tech support to find out. It looks like the surcharge might be in there twice. I can send you a $3 gift certificate if it helps?

OK. I screwed the order up and didn't complete it the first time for some idiotic reason, but now payment is in. I don't know what the hell I did the first time! Also, the unknown 3.98 was removed upon completion. What an F'n moron! Thanks man...

Payment sent! :D

SHIZZAM! ... i mean, paid.

I have 7 paid orders.

Get off your broke a$$es and pay the man. :D

http://farm4.static.flickr.com/3280/2380362515_38a13826cb.jpg?v=1207084179

Well i started the thread and im the last to pay, now i feel like a dummy DAWM IT!!!!!!

Thanks Andy

Newfie.

Well, I wasn't going to get one as I am a broke college student. But I guess I'm getting one too. Payment sent!

Well, I wasn't going to get one as I am a broke college student. But I guess I'm getting one too. Payment sent!

Don't fight the urge to mod, it's pointless. :D

Don't fight the urge to mod, it's pointless. :D

Hey i tried to. I even backed out of the GB. But i was sitting @ work and it was calling me. I kept hearing "Buy it Buy it"

Oh, I'm not fighting... But my bank account is!

Oh, I'm not fighting... But my bank account is!

I feel you there

I want to install my pulley first, so if I fk anything up its on my Jeep. :D
After that, if anyone wants to drive to Chicago to get their pulley installed; I will be happy to install it for you.
Installation cost will be FREE for anyone in this group buy. Just send me a PM and we can arrange the details. We can have a pulley install day.

I'm paid up too

Well, I wasn't going to get one as I am a broke college student. But I guess I'm getting one too. Payment sent!

It means just less beer money that's all!!:D

Don't fight the urge to mod, it's pointless. :D

I hear ya on that one!!

Hey i tried to. I even backed out of the GB. But i was sitting @ work and it was calling me. I kept hearing "Buy it Buy it"

Damn that little voice in our heads!! That little voice has gotten me in more trouble than anything. But then again, that little voice has also cause more fun in my life than anything!:D

Damn that little voice in our heads!! That little voice has gotten me in more trouble than anything. But then again, that little voice has also cause more fun in my life than anything!:D

oh soo true

PAID via Paypal

I'll be paying Monday :) or Sunday perhaps??? When I get back from visiting friends!

I paid Andy

I appreciate all of you paying Andy. Now how 'bout each of you sending me $20? :D

Couldn't pass this up. Paid.

ok guys, I have to close this now. I have all my pullies sold. Thanks for everyone that participated.

Sweet Andy, when are the shipping out?

5 will go out on Monday. I ordered 15 more belts today to be overnighted so hopefully I can ship all of them out on Monday, but it may be Tuesday at the latest.

Thats cool. No rush on mine just so you know

ok guys, I have to close this now. I have all my pullies sold. Thanks for everyone that participated.
How is this, i'm # 12, i just got home from work and is trying to pay , and you closed this buy. whats up:confused:

^^I think if your on the list your fine, just no one can be added to the list now.

What the hell!!! I want my pulley I dont have access to my accounts right now because I'm on a mini vacation visiting friends!!!!! I'm number 3!!!

Am I seriously getting JAYED/Jipped/beat/snuffed/fuacked over over right now because I dont have access to my bank accounts and paypal right now? I'm online on my iphone!!! I can't afford the full price so thats why I was getting in on this!!

omg i hope this gets cleared up! this is something i wanted and have only 170 for! please clear this up or im going to be so mad and be pissed on the forums cause of this!!!!

Anybody know how to order it on the powerported.com site and get the gp price? I just tryed and it was still the original price, or do we get refunded after the fact or do we have to type in some secret code lol, like gp, or i belong to the forum.:D

well i,m waiting 4 an answer, i can wait till next week but i want that same price.

I want in to, am I to late?

I want in to, am I to late?

Yes your too late.

I'm not!!! Ugh! Whats the point of a list if other people who are never even on here come click the links and steal MY reserved pulley!!!!

ok guys, I have to close this now. I have all my pullies sold. Thanks for everyone that participated.

Yea really. THIS GROUP BUY is closed.

It better not be completely closed I just need to send me payment in! I'll be able to do that tomorrow!

How is this, i'm # 12, i just got home from work and is trying to pay , and you closed this buy. whats up:confused:

PM was sent to you.

What the hell!!! I want my pulley I dont have access to my accounts right now because I'm on a mini vacation visiting friends!!!!! I'm number 3!!!

It better not be completely closed I just need to send me payment in! I'll be able to do that tomorrow!


PM me when you are back in town. Your taken care of.


I ended the group buy when I had 3 pullies left to make sure that everyone that got in on the list would be able to get one. I will go ahead and adjust the price again, but please understand that all new orders will have to wait till more pullies come in. I will order them on Monday and should have them by Wednesday. Here is the link. $170 for the pulley and the bolt plus shipping which has been about $15 on average.
http://purehorsepowerperformance.com/25underdrivepulley.aspx

PM was sent to you.






PM me when you are back in town. Your taken care of.


I ended the group buy when I had 3 pullies left to make sure that everyone that got in on the list would be able to get one. I will go ahead and adjust the price again, but please understand that all new orders will have to wait till more pullies come in. I will order them on Monday and should have them by Wednesday. Here is the link. $170 for the pulley and the bolt plus shipping which has been about $15 on average.
http://purehorsepowerperformance.com/25underdrivepulley.aspx
OK, thank you;:)

Yes your too late.

I'm not!!! Ugh! Whats the point of a list if other people who are never even on here come click the links and steal MY reserved pulley!!!!

Boy am I going to enjoy putting YOUR pully on my truck...

THANKS!

^^^^Your welcome!

Thanks PPP for helping me out!!! I'll pay Monday when I'm back home.

Andy, do you happen to have overdrive pulleys for the alternator? I've been watching this since you guys started, and was really thinking about getting in, but I think I may have a charging issue. My truck idles ALOT, its used to jump start everything from cars to UPS trucks, and my boss wants me to consider putting emergency strobes in it. I'm really worried that underdriving the alternator will cause problems.

in 2 years we have never had a charging problem nor have any of our customers so we have not invested into making an overdrive pulley. You could always raise your idle up 100rpm to have the same amount of idle charging capability.

Alright, I can still order right? It just won't ship until you get more in.

Hope so, because I just did. :)

Any chance mine has shipped yet?

Any chance mine has shipped yet?

not to nag.. but... X2 :D

...............x3 just curious

x4

:)


.

X5

Sorry to bug

payment sent!

check your emails. I got one earlier from them saying it was shipped.

check your emails. I got one earlier from them saying it was shipped.

whats good, where are you going to get it installed ?

whats good, where are you going to get it installed ?

I asked AJ if he would do the install. He said aight. But I might put it off for a while. Thinkin about adding a few more goodies @ the same time.

I asked AJ if he would do the install. He said aight. But I might put it off for a while. Thinkin about adding a few more goodies @ the same time.

I know what you mean, i still have to install my high-flow cats. i will buy my cam next week;)

Has anyone received their pulley yet? I paid extra for Prority shipping 10 days ago and still haven't received it yet. :(

I think Andy is waiting on more pulley bolts to come in. I think he only had like 4. I know he is waiting on something...

We shipped 10 out and hopefully the rest will go out tomorrow.

Has anyone received their pulley yet? I paid extra for Prority shipping 10 days ago and still haven't received it yet. :(


Never pay for expedited shipping on a group buy. I will refund the expedited shipping charge tomorrow to you. Your only 1-2 days from us with ground shipping anyway. We are shipping in the order which we received orders. Anyone not needing the bolt can gurantee shipment tomorrow. Please PM me if you do not need the bolt.

Never pay for expedited shipping on a group buy. I will refund the expedited shipping charge tomorrow to you. Your only 1-2 days from us with ground shipping anyway. We are shipping in the order which we received orders. Anyone not needing the bolt can gurantee shipment tomorrow. Please PM me if you do not need the bolt.

I don't want the money back--you've already given me a fantastic deal on the pulley. I'm only concerned with the fact that I'm only at the shipping address for another four days. If the pulley won't ship by Wednesday for Friday delivery I will need to change the shipping address.

I will definitely keep you posted and make sure we get it to the right address and thanks for your patience.

I need the bolt so no rush on mine. Im guessing you are holding my rods to ship with the pulley Andy?
You might just want to hold on to that stuff and ship a few other things with it :)

Talk to you tomorrow

We shipped 10 out and hopefully the rest will go out tomorrow.
By any chance, did you ship out any pulleys today, or are you waiting for more to come in ?

i got mine today

Just wondering if mine got shipped.

Thanks,

John

I need to know who paid using paypal only. This does not include anyone that used the website. If you went to the link and paid on our website using Paypal, I do not need a response from you. I need to know who never went to the website and just sent funds via paypal and not through the website.

That would be me sir Andy!

I have the following:

Mike C
Mike V
Anthony H
John K

Is there anyone else?

Thanks Andy! Ill be watching the mail. And my email :) I think I can probably work something out but we will see what you got for me.

That might be me to.

I need to know who paid using paypal only. This does not include anyone that used the website. If you went to the link and paid on our website using Paypal, I do not need a response from you. I need to know who never went to the website and just sent funds via paypal and not through the website.

I also paypal'd you directly.

Edit: Whoops..I see that you already you have me on the list. (John K)

Mine shipped today! :)

Did mine ship yet or what? I'm tired of waiting! LOL! Seriously, did it? Since I paid 4th or 5th, I am assuming it went out with the first shipments and will be here by tomorrow or Friday, is that right?

Did mine ship yet or what? I'm tired of waiting! LOL! Seriously, did it? Since I paid 4th or 5th, I am assuming it went out with the first shipments and will be here by tomorrow or Friday, is that right?

I love it when people ask me if theres has shipped but dont tell me their name. lol. JK. Whats your name and I will look into it.

Mine came in yesterday and will go on Saturday.:D

This is who I shipped so far.
Travis V
Paul H
Philip A
Anthony V
Nick M
Andy S
Jeremy S
Wayne D
Will H
Eric K
Anthony W
Matt K
Calvin C
Harrison Z
Daren P
Jerry S
David P
Mike C
Mike V
Anthony H
John K

This is who I shipped so far.
Travis V
Paul H
Philip A
Anthony V
Nick M
Andy S
Jeremy S
Wayne D
Will H
Eric K
Anthony W
Matt K
Calvin C
Harrison Z
Daren P
Jerry S
David P
Mike C
Mike V
Anthony H
John K
just wanted to know about J Justice, jsjahonda, r u shipping soon ?

Andy, after still reading this thread you are correct it was a bad idea to suggest that these guys use the oven method. My bad, Im mechanically inclined and didtn realize the liabilities you must face as a business owner.

As for all the people asking did mine ship, wouldnt it really be easier to pick up the phone ?

There are 6 people ahead of you and we are out of pulleys. We order 15 more and they will be here tomorrow or Monday. I am creating the labels today so we can send the remainder of the orders tomorrow or Monday when they come in. Here is who is left.
Dan L
Mike A
James L
Paul S
Robert N
Mike L
Jason J
Jason C
Mike E
Clay J


Thanks for everyones support, this was allot larger than we expected. 35 Pulleys sold.

I know you haven't forgotten that I want one, when my 426 is ready to be sent to Fast Specialties:D

No sir, yours is sitting at ERL.

I love it when people ask me if theres has shipped but dont tell me their name. lol. JK. Whats your name and I will look into it.

LOL! Sorry 'bout that! I just figured you would be smart enough to play Sherlock Holmes and match my screen name with the paypal payment! :eek: JUST KIDDING! :D I'm on the list you posted so no worries! i'll get it when I get it...

I just got a nasty email from one of the buyers of the group buy about how long it is taking. I am very sorry for the length of time it is taking, but we sold more pulleys than what we had on the shelf. Rather than ending the group buy, we left it up there and ordered more pulleys in. We are only making $7 per pulley, so it is not worth the frustration of getting emails from customers that are pissed about the 2 weeks it has taken. If anyone is tired of waiting, just let me know and I will gladly refund your money back to you with no hard feelings, but when I get emails telling me how stupid this is, it makes me not want to do group buys, so I ask that if you want a refund, just let me know and I will gladly issue it, but please dont send me an email telling me how stupid this is and that if you dont receive by a certain date your going to cancel your order. I hope this doesnt come across as rude, its just frustrating when you offer such a good deal and people still find a way to complain. We are doing the best that we can and everyone will have their pulleys by the end of next week.

Thanks to everyone else who has been patient.

Who would be DUMB enough to complain about how long it takes,he could have closed the sale at 11 and then you would have been paying full price or $hit out of luck.At lease Andy and PPP were good enough to help use out and do the group buy and a GREAT price.SO STOP WHINNING AND WAIT!!!!!!,or ask for you money back because im sure somone else will jump on the deal.

Sorry you have to deal with A$$HOLES ANDY

Newfie.

Damn, I was delighted with the savings. .

Guys, don't be @$$es when we get to save money.

Want to be an @$$? Pay full price then you have the right to complain about slow order processing.

Most of our supporting vendors are not large corp's with hundreds of people working in order fulfillment. Our group buys are large spikes in their business and they have to work extra hard for a lower margin. Just be happy with the savings.

Whomever is complaining is a real douchebag.

Can we come to your work and whine about something that you are doing for $7?

Hey Andy! Do you happen to have a tracking number or status on my Pulley? I know you said it shipped last wednesday. I thought id have it by now considering we aren't very far away. Thanks

Sorry for your troubles Andy.... It was good talking with you on Saturday. Some people are jack asses and being in retail, unfortunatly, you gotta deal with them. The the person who wrote the email, if you're reading this, good God man, what is your issue? Cancel the order and pay alot more somewhere else. I'm sure Andy can sell it pretty damn quick. That's just flat out plain and simple rude!

Andy I left you a PM about your other thread and wanted to let you know I got the pulley today. Weird it never tracked, but oh well it's here. Could you please respond to my PM too. I'd like to get that going if we can. Thanks again

Mine arrived in sunny Florida today, via stealth UPS no tracking delivery.

Now, to find a qualified installer... Or do I wait for my warranty to end in April...

Still havent seen my pulley.....

Still havent seen my pulley.....

Me neither, but then again I was the last to order. Guess its not gonna be installed before my tune on Saturday. Oh well.:(

I guess I better go ahead and order mine so the order can start to get processed.

Sent Andy a PM about mine but no answer?????

I have no PM's scoutermike. Please resend.

Me neither, but then again I was the last to order. Guess its not gonna be installed before my tune on Saturday. Oh well.:(

Mike, that makes two of use. I am not real happy about it. Paid for the parts on 2/21/09, still nothing.

20 pullies on the shelf.
42 sold

first 20 shipped out
25 more ordered
7 were on the shelf in the US
7 shipped out to the next 7 custotmers
15 orders remaining
18 pullies are on cargo ship from AUS to the states

They are scheduled to be at US warehouse on Friday at which time all remaining orders will be shipped.

I am very sorry for the delays, but I also posted that there could be delays with the large number of orders.

We will host it if you want. I have 20 sitting on the shelf right now. I just need to get more belts in, but thats easy enough. How much interest is there? I will sell for the following.

5-10 units: $175 plus $20 for bolt/belt
11+ units: $150 plus $20 for bolt/belt

Shipping is additional and usually around $15.

Is this price still available? If so I want to get one with the belt and bolt. I understand about the delays and I'm ok with that

I have 3 that are not spoken for, but I have already adjusted the price on the website to $165 + $20 for the belt and bolt.

http://purehorsepowerperformance.com/25underdrivepulley.aspx

So if I want one do I pay $150 + $20 or $165 +$20?

This is who I shipped so far.
Travis V
Paul H
Philip A
Anthony V
Nick M
Andy S
Jeremy S
Wayne D
Will H
Eric K
Anthony W
Matt K
Calvin C
Harrison Z
Daren P
Jerry S
David P
Mike C
Mike V
Anthony H
John K
I haven't seen mine yet.

Thanks,

John

ok I went ahead and order one since you said you had a few not accounted for and paid by paypal it should be under Jason R and I even put a note on it saying my forum name here so you could match it to me. order number is 2317.

I was originally number 14 on the list and paid right away. I never even made the shipped to list. Hopefully they will arrive soon.

Mike A

All pulleys are in the country and in transit! Woo Hoo.

Yes! Nice work Andy. I know you said you shipped mine like 3 weeks ago but it must have been another Anthony lol because I haven't seen it. Its all good. Ill be watching for mine now. Thanks Andy!

Cool I'll keep my eye out for the delivery truck, thxs

I got my tracking number yesterday. Somebody screwed up a bit though Andy, because the invoice said USPS Priority and the tracking number is a UPS number (which is valid, I checked).

Can I get the tracking number for mine?

and mine. Thanks Andy!

Called Andy yesterday. He said they were to ship out in the afternoon. He gave me my tracking number and a check of it this morning shows it in transit and being delivered today. Out of Elsemere, Kentucky last night and delivered to Livonia, Michigan today. Gotta luv UPS.

Andy are all the pullies shipping out now?

I think they all shipped yesterday.

PM me if you have not received a tracking number

Pm sent good buddy!

Hey Andy, can you check on these? I got 2 emailed numbers from you guys through UPS, and neither shows any activity. The first one, I think I got a message was cancelled, but the second has just been on Billing Information Received since the 31st.

Thanks.

Mike, yours and Anthonys are going out today guranteed. As a matter of fact, all orders are shipping today which is about 7 guys. Thanks to everyone that supported this, we sold right at 50 underdrive pullies during this sale.